waterproofing properties without the need for degradation and is a definite alternative to bitumen and traditional insulation, which becomes completely colorless after use on the surface. This adhesive, which is based on acrylic resins and uses nanotechnology, has the ability to combine easily in any type of slurry. After application, it has a strong bond with the structure and has an excellent penetration on the surface. – Be. This material has a significant temperature range and is environmentally friendly. It is highly resistant to detergents, UV rays and gas. It is fragrant, anti-moss, algae and bacteria and does not allow the growth and accumulation of these substances on the surface. Negative and positive waterproofing agents are easily tolerated and are known to be a versatile material in the insulation industry. . In addition to Borna powder, it is a ready-to-use microsilica mortar that, after mixing it with water, provides a good restorative paste for repairing concrete or shallow concrete columns.
Due to the presence of compatible polymers in its composition, in addition to the ability to form and adhere to various types of materials and concrete and cement surfaces, this product reduces surface permeability.
Adhesive BS9000
It can be applied on all permeable surfaces such as cement, concrete, stone, plaster, brick, wood, etc. and is used in the following cases:
A: Use for insulation
This material is used as a topcoat for final coating and insulation of surfaces such as swimming pools, building facades of concrete or drinking water tanks, tilots, roof gardens, terraces, parking lots, etc. This adhesive is applicable in thicknesses of 5to300m
B: Use for resin
This material can be combined with a proportion of water (depending on the type of work) and applied with a brush or pistol to resin all the places and facades where the color and appearance of the work should not change. Obviously, the use of products on impermeable surfaces such as polished and pre-resinous rocks, glazed ceramic tile surfaces, non-raw wood and all surfaces with oil-based paints or additives (various thinners, bitumen, isogum, other derivatives) Oil) Pre-coated, not directly possible. Therefore, these layers must be removed before execution. Due to the power of water prophylaxis and resistance to negative and positive pressures, this product has the highest application in the field of specialized insulation
Applicable by brush and pistol, no need for cementing and mortar mortar after application, reducing the thickness of the insulation layer and no restriction on the walls and heights, no transpiration and sealing of the sealing layers over time, no vulnerability And the perforation of the layer against the natural stresses of the structure and the reduction of the cost of aggregates and materials, the ability to combine with a variety of acrylic paints.
They can be applied on all cement, concrete, stone, gypsum, brick, wood, etc. surfaces. Make sure that the final surface is firm, that there is no subsidence, and that there are no surface or deep cracks in the substructure.
Clean the surface of the structure from any contamination (grease, dust, petroleum products such as mold oil and oil paints, old coatings, etc.) and pre-clean the concrete or mortar surface using water spray method. Do.
General method of product execution (Execution methods may vary depending on the location.)
Solution A: In all stages, one unit of the product is combined with one unit of water, which is called solution A for brevity.
A: Sealing 100% of cement surfaces
• Apply solution A with a brush on the surface of both hands to the drying distance of the previous layer.
• Combine one unit of cement and two units of sifted rock powder (micronized silica) separately, add it to solution A, then apply the smooth flowing brush with a brush on the surface of both hands at a dry distance. Run the previous layer.
• Run step one again.
B: Color sealing (waterproof paint)
If you want to paint the structure, you can use a combination of three acrylic paint units (water base) with one unit of product in the third step.
A: Sealing and resin façade
Apply solution A with a brush or pump on the surface, both hands completely and with the distance of the appearance of the first layer.
D: Combination with powder component
In combination with a powder component, it is made with a ratio of one to three mortars or slurries, which seals the walls or surfaces to seal the surfaces.
Approximate consumption of the product
For each square meter of sealing, 600 cc and for each square meter of resin 300 cc.
The approximate composition of the product
One unit of product + one unit of water
• It is recommended to wear glasses, gloves and work clothes during the performance.
• If the glue comes in contact with the skin, it must be washed with water before drying.
• In case of contact of the glue with the eyes or penetration into the mouth, wash immediately with plenty of water and see a doctor.
To protect the product for a long time, keep it clean and without mixing with any additives (even water) and close the lid tightly (according to storage conditions).
Propertesi | Standard | the amount of |
Appearance | White emulsion | |
Solubility | Water soluble | |
Type | Acrylic | |
Mechanical capability | Excellent | |
Stability stability | 12days | |
Solid percentage | ASTM 2369 | 40±1 |
viscosity (cp) | Brookfield RV , 23 °C | 700-1400 |
PH | ASTM D1293 | 9 – 5/7 |
thermal resistance | 400 | |
Minimum film formation temperature | ISO 2115 | +5 |
density | ASTM D1475 | 06/1 -02/1 |
Maximum free monomer (%) | 3/0 |
Propertesi | Standard | Except powder |
Volumetric mass | kg.L-1 | 1.67 |
Appearance | Gray | |
Type | Polymer composition |